PAGE UPDATE
27.11.2011
|
CARBURETOR SPARES
Carburetor spares for Ural and
Dnepr motorcycles.
|
|
|
| |
|
We stock £1000s of spares for Ural,
Cossack, Neval, Uralmoto, Dnepr, Dnieper, KMZ, IMZ, but here
are a few of the harder to find bits and pieces. This page shows
a small selection of the Carburetor parts we have in stock.
For even more Russian spares please take a look at the
Russian Spares link in the main menu We are always on the hunt for hard to find
Russian bike spares, and if we really can't find them,
or when the original part can be improved, we develop and make
our own alternative.
Please note - we do not deal in used parts, or broken parts.
If we can't get it in unused new condition, we don't sell it.
|
|
|
| Carb Mount - Ural 650 to Jikov.
For a very short time Ural 650cc motorcycles were fitted
with a Jikov Carburetor made in the Czech Republic. The
mounts are no longer available through the factory, but
we have managed to get a small quantity manufactured as
a pattern part. These will fit Ural 650cc cylinder heads
with stud centre spacing of 51 to 57 mm. These can also
be used to mount other makes of carb with approximately
34mm outside diameter stubs. |
| Part - F23806/JIKOV pair |
Price
- £55.00 |
|
|
|
|
| Carb Gasket - K65. Extra
thick gasket between head and carburetor for K65 only. The
standard gaskets coming from Russia are now less than 2
mm thick. These are made as exact copies of the original
gasket designed by the factory in the first place. They
are 4.10mm thick and compress to 4.00 mm in use. This helps
to stop heat transfer from the head to the carburetor. |
| Part - F23838/x1 |
Price -
£6.00 |
| Part - F23838/pair |
Price
- £10.00 |
|
|
|
| Carb Mount - Ural 750 to Keihin.
Fit all 750cc Urals originally fitted with the Keihin
CV carburetors with stud centres of 57mm. Our ones have
an enclosed steel insert so they are rigid enough to support
the carburetor. Please note there where a few early 750
OHV Urals with stud centres of 52 to 54 mm. We have a
few customers who have managed to file the mounting holes
oval to fit these bikes. Supplied with clips and screws
as shown |
| Part - F23825/x1 |
Price
- £32.00 |
| Part - F23825/pair |
Price
- £62.00 |
|
|
|
| Carb Kit - K63/K65. Complete
carb kit including carb top, the emulsion tube and jet holder,
and complete choke plunger. So many people give up with
these carburetors and fit something else when really all
they need is a really good clean and setting up properly.
Often the emulsion tube is completely blocked on bikes that
have been standing with old fuel in them. This kit could
save them. You will need one kit per carburettor. Genuine,
not nasty cheap copies from eBay. Ours work. |
| Part - F24010/K65 x1 |
Price -
£28.00 |
| Part - F24010/K65 x2 |
Price
- £50.00 |
|
|
|
| Carb Kit - K68. Kit of
parts to overhaul the K68 carburetors fitted to some Ural
650 and 750 bikes. The K68 carburetors are handed left
and right so we only supply these kits in pairs. |
| Part - F24010/K68 pair
|
Price
- £36.00 |
|
|
|
| Carb Kit - Keihin. Simple
kit for the Keihin CVK carburetor fitted to Ural Tourist,
Dalesman, Wolf, etc. The float needle should cure the minor
leaks associated with wear in the viton tip. The replacement
slow running needle complete with o-ring will help to cure
the tick over setting problems associated with worn or damaged
needle taper. |
| Part - F24010/KEIHIN x1 |
Price -
£12.00 |
| Part - F24010/KEIHIN x2 |
Price
- £20.00 |
|
|
|
| Carburetors - 301 Upgrade.
Early Ural Motorcycles including M72 and M63/M66 used
a simply dreadful carburetor know as the K301. Almost
any other carburetor would be an improvement. These pattern
carburetors have the advantage of bolting straight on
and looking almost the same as the originals. They work
much better than K301s. We supply them as a pair with
gaskets. You may need to make up new cables depending
on which throttle you have on your bike. |
| Part - F23803/301 pair |
Price
- £130.00 |
|
|
Picture coming
soon |
Carburetors - 301 Upgrade Spares
Kit. Great news for our customers who have already
purchased the 301 upgrade carburetors (F23803/301). We
now have some spares kits in stock. This includes a float,
float needle, throttle needle, air adjusting screw, throttle
slide adjusting screw.and the little gaskets from the
top and bottom of the carburetor. |
| Part - F23803/301spares x1 |
Price -
£13.00 |
| Part - F23803/301spares
x2 |
Price
- £25.00 |
|
|
|
|
To order or for more information
please phone us on 01295 712900 between 2pm and 5pm
Tuesday to Saturday.
Postal Charges - £6.00 any order of any value
in the UK*
Flat charge of £6.00 applies to all UK orders*.
Orders will generally be sent by APC and will need a
signature on delivery.
All deliveries are tracked and insured.
Orders taken before 4pm Wednesday are posted Thursday
morning for delivery to you on Friday.
Orders taken before 4pm Saturday are posted Monday morning
for delivery to you on Tuesday.
* Sorry, this does not include NI, Scottish Highlands
or off shore Islands as defined by APC, but we will
quote the best price possible when you order.
|
|
|
|
